Updated NACE-CIP1-001 Dumps PDF - NACE-CIP1-001 Real Valid Brain Dumps With 100 Questions!
100% Free NACE-CIP1-001 Exam Dumps Use Real CIP Level 1 Dumps
NEW QUESTION # 51
How many gauge readings does SSPC-PA 2 require within a 4 cm (1.5 inch) diameter circle?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: D
NEW QUESTION # 52
Common errors that may produce inaccurate readings when using a Dial-Type Magnetic Pull-Off Dry Filth Thickness (DFT) gauge include:
Select All That Apply
- A. Rotating the dial too fast when taking measurements
- B. Failing to determine the base metal reading (BMR)
- C. Taking measurements too far from the edge of a surface
- D. Measuring ditty, tacky, or soft films
Answer: A,B,D
NEW QUESTION # 53
Most industrial coatings are:
- A. Resistant to concentrated sulfuric acid
- B. Inorganic
- C. Resistant to temperatures above 200C
- D. Organic
Answer: D
NEW QUESTION # 54
Silicone coatings are typically:
- A. Used as a sacrificial primer
- B. Applied in very thick films
- C. Used strictly in immersion service
- D. Applied in very' thin films
Answer: D
NEW QUESTION # 55
SSPC SP 1 identifies the use of:
- A. A wide variety of materials
- B. Inorganic solvents
- C. Organic solvents
- D. Biodegradable detergents
Answer: A
NEW QUESTION # 56
What is used to determine compressed air cleanliness?
- A. Psychrometer
- B. Needle pressure gauge
- C. Blotter test
- D. Profilometer
Answer: D
NEW QUESTION # 57
Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners' representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:
- A. Bring the matter up at the pre-job conference
- B. Meet separately with the coating manufactures' representative and coating application company in advance of the pre-job conference
- C. Gather data and attempt to meet with the owner's representative in advance of the pre-job conference
- D. Default to the owner's Inspection and Test Plan
Answer: A
NEW QUESTION # 58
Removal of welds splatter is required:
- A. When specifically identified in the owner's specification
- B. When NACE/SSPC abrasive blast standards are specified
- C. On every job
- D. When ISO abrasive blast standards are specified
Answer: A
NEW QUESTION # 59
You are the NACE Inspector on a job where the Owner's specification requites you to perform a twice daily check of blast pressure at the nozzle. It is now day 30 on the job and all of your readings have been within compliance. The Contractor complains that these checks taking up much time and in view of the compliant results they are unnecessary.
Your FIRST preferred course of action is to:
- A. Skip the checks as you are. confident the blast pressure is OK
- B. Keep doing the checks and consult the Owner's representative for direction
- C. Keep doing the checks regardless
- D. Skip the checks and just record the same readings as you have been getting
Answer: B
NEW QUESTION # 60
As a NACE Coating Inspector your responsibility with respect to safety is to:
- A. Act in accordance with the site safety requirements and set an example
- B. Assume the role of the Safety Inspector
- C. Check the PPE used by the Applicators
- D. Check the credentials of the Safety Officer on site
Answer: A
NEW QUESTION # 61
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. No, because there is no real difference in the standards
- B. Yes, because the 'two standards are not equivalent
- C. It depends on which hand tool the Contractor selects
- D. It depends on which power tool the Contractor selects
Answer: A
NEW QUESTION # 62
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Call the coating manufacturer for clarification
- B. Call the person who wrote the specification for clarification
- C. Use the job specification as a guide
- D. Use the product data sheet as a guide
Answer: C
NEW QUESTION # 63
Which is a component that supplies most of the features and functions of the material?
- A. binder
- B. solvent
- C. additive
- D. pigment
Answer: A
NEW QUESTION # 64
The main responsibilities of the inspector are to
- A. demonstrate to the contractor how to apply the coating.
- B. observe and direct the work of the contractors.
- C. direct and perform the work stated in the specification.
- D. observe and report the quality of the work performed.
Answer: D
NEW QUESTION # 65
The least effective method of surface cleaning is most likely
- A. water blasting.
- B. power tool cleaning.
- C. dry grit blasting.
- D. hand tool cleaning.
Answer: D
NEW QUESTION # 66
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is:
- A. Level 1
- B. Level 4
- C. Level 2
- D. Level 3
Answer: D
NEW QUESTION # 67
Solvents are added to coating formulations to
- A. dissolve binders and form liquid coatings.
- B. decrease film permeability.
- C. increase film permeability.
- D. provide color.
Answer: A
NEW QUESTION # 68
......
Pass Your NACE-CIP1-001 Exam Easily With 100% Exam Passing Guarantee: https://www.braindumpsvce.com/NACE-CIP1-001_exam-dumps-torrent.html
NACE-CIP1-001 Dumps are Available for Instant Access: https://drive.google.com/open?id=1SQxWO_6BQdU6zWyxQGpxO8R-S-KYEhX5