NACE NACE-CIP1-001 Practice Verified Answers - Pass Your Exams For Sure! [2021]
Valid Way To Pass CIP Level 1's NACE-CIP1-001 Exam
NEW QUESTION 13
Which is a component that supplies most of the features and functions of the material?
- A. pigment
- B. solvent
- C. binder
- D. additive
Answer: C
NEW QUESTION 14
On a blast-cleaned surface, Ian ultraviolet light is generally used to detect
- A. sulfates
- B. grease and oil
- C. soluble chemical salts
- D. inhibitor residues
Answer: B
NEW QUESTION 15
If the project specification DOES NOT state the specific DFT measurement standards, the inspector should use
- A. a recognized industry standard like SSPC-PA 2 that is broadly accepted
- B. their best judgment based on similar projects and specifications.
- C. a detailed checklist and document the lack of a standard.
- D. NACE 2/SSPC SP10
Answer: A
NEW QUESTION 16
The Inspector should record the serial numbers of inspection instruments:
- A. Only when verifying accuracy of the instrument
- B. Only if the instrument is suspected of not working properly
- C. Only if the specification requires it
- D. Each time the instrument is used
Answer: D
NEW QUESTION 17
It is good practice for the NACE Inspector to have instrument calibration certificates available:
- A. Only if the specification requires it
- B. In the field only
- C. At all times
- D. In the office only
Answer: C
NEW QUESTION 18
If inspectors identify issues of non-conformance during an inspection, they should
- A. wait until the final report is being prepared to identify the issues in writing so they are fully documented
- B. instruct the contractor's personnel in how to correct the issue so the project is not delayed
- C. inform both the Contractor and the inspector's supervisor so they can take appropriate corrective actions
- D. perform additional tests secretly to ensure there are no other potential issues at the site
Answer: C
NEW QUESTION 19
If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a
- A. wet film thickness (WFT) measurement.
- B. dry film thickness (DEI) measurement.
- C. vial lest.
- D. blotter test for the presence of oil and water.
Answer: D
NEW QUESTION 20
Digital hygrometers
- A. consist of a bimetallic sensing element protected from wind gusts.
- B. are used to measure temperature from a distance.
- C. determine relative humidity, air temperature, and dew point temperature:
- D. use a thermocouple in contact with the surface to measure temperature
Answer: C
NEW QUESTION 21
Safety Data Sheets must be carefully reviewed by:
- A. The Owner's personnel
- B. The Application personnel
- C. All personnel involved in the job
- D. The Inspection personnel
Answer: C
NEW QUESTION 22
Stripe coats are generally applied to:
- A. Welds
- B. Complex geometric shapes
- C. a), b), and c)
- D. Edges and corners
Answer: C
NEW QUESTION 23
When performing tests for oil and grease using an ultra-violet light, the NACE Inspector should be aware that:
- A. Synthetic oil or grease may not be identified
- B. Presence of weld spatter may produce a false positive
- C. Chloride salt may produce a false positive
- D. Ultra-Violet light may contaminant the surface
Answer: A
NEW QUESTION 24
Upon arrival of coating materials, the inspector should
- A. observe and document the amount of material and batch numbers.
- B. observe aryl document that the applicator WFT at regular intervals during application.
- C. observe and document time frame and environmental conditions between each coat.
- D. review coating contractors' plans for storage of coating materials and confirm they meet national, local and owners' fire and environmental regulations.
Answer: A
NEW QUESTION 25
NACE Level 1 Inspectors have been trained to perform:
- A. Visual inspection and Non-destructive testing
- B. Visual inspection only
- C. Visual inspection, Non-Destructive and Destructive testing
- D. All types of inspection
Answer: A
NEW QUESTION 26
The primary difference between Non-Convertible vs. Convertible coatings is:
- A. Convertible coatings do not undergo a chemical change during curing whereas Non-Convertible coatings do
- B. Non-Convertible coatings cure by co-reaction whereas Convertible coatings do not
- C. Convertible coatings cure solely by solvent evaporation whereas Non-Convertible coatings do not
- D. Non-convertible coatings do not undergo a chemical change during curing whereas Convertible coatings do
Answer: D
NEW QUESTION 27
Removal of welds splatter is required:
- A. When NACE/SSPC abrasive blast standards are specified
- B. When ISO abrasive blast standards are specified
- C. When specifically identified in the owner's specification
- D. On every job
Answer: C
NEW QUESTION 28
You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3.
Could this have any impact on the final surface preparation appearance?
- A. It depends on which power tool the Contractor selects
- B. Yes, because the 'two standards are not equivalent
- C. No, because there is no real difference in the standards
- D. It depends on which hand tool the Contractor selects
Answer: C
NEW QUESTION 29
In the event of a conflict between the project specification and the coating manufactures' product data sheet, the Inspector's first course of action should be too:
- A. Call the coating manufacturer for clarification
- B. Call the person who wrote the specification for clarification
- C. Use the product data sheet as a guide
- D. Use the job specification as a guide
Answer: D
NEW QUESTION 30
When using the ISO comparator in accordance with ISO 8503, if the surface profile does not directly compare to one of the four segments the inspector should:
- A. Record the segment with the more aggressive profile
- B. Record the segment with the less aggressive profile
- C. Use another method as the comparator method is too subjective
- D. Record your result by identifying two segments
Answer: B
NEW QUESTION 31
Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition:
- A. Rust Grades A-D
- B. Rust Grades 1-4
- C. Surface Condition H
- D. Surface Conditions E-G
Answer: A
NEW QUESTION 32
......
NACE NACE-CIP1-001 Pre-Exam Practice Tests | BraindumpsVCE: https://www.braindumpsvce.com/NACE-CIP1-001_exam-dumps-torrent.html
NACE-CIP1-001 practice test questions, answers, explanations: https://drive.google.com/open?id=1SQxWO_6BQdU6zWyxQGpxO8R-S-KYEhX5