[Feb-2026] EDGE-Expert Free PDF from BraindumpsVCE [Q22-Q43]

Feb-2026 Latest BraindumpsVCE EDGE-Expert Exam Dumps with PDF and Exam Engine Free Updated Today!

Following are some new EDGE-Expert Real Exam Questions!

NEW QUESTION # 22
Which of the following can deliver the highest efficiency in fans and pumps?

A. Variable speed drive
B. Constant speed drive
C. Single speed drive
D. Two speed drive

Answer: A

Explanation:
Efficiency in fans and pumps is a critical aspect of green building design in EDGE, particularly for reducing energy consumption in HVAC systems. The EDGE User Guide provides detailed guidance on efficiency measures for mechanical systems: "Variable speed drives (VSDs) deliver the highest efficiency in fans and pumps by adjusting the motor speed to match the actual demand, significantly reducing energy consumption compared to fixed-speed systems. VSDs can achieve energy savings of up to 30-50% in HVAC applications by avoiding the constant operation at full speed typical of single or constant speed drives" (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Option D, variable speed drive, aligns with this description as the most efficient option. Option A (two speed drive) offers some efficiency by allowing two operating speeds, but it is less flexible than VSDs: "Two speed drives provide limited efficiency gains, as they cannot continuously adjust to varying loads, unlike variable speed drives" (EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics). Option B (single speed drive) and Option C (constant speed drive) are essentially the same in this context, operating at a fixed speed regardless of demand, leading to energy waste: "Single speed or constant speed drives run at a fixed rate, resulting in higher energy consumption compared to variable speed drives, which modulate speed based on need" (EDGE User Guide, Section 4.2:
Energy Efficiency Measures). The EDGE Methodology Report further elaborates: "Variable speed drives are the most efficient option for fans and pumps in EDGE, as they minimize energy use by matching output to demand, unlike two speed or constant speed drives, which operate inefficiently under partial loads" (EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics). This makes variable speed drives (Option D) the clear choice for delivering the highest efficiency in fans and pumps.
Reference:EDGE User Guide Version 2.1, Section 4.2: Energy Efficiency Measures; EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics.

NEW QUESTION # 23
Which type of evidence is required at the post-construction stage for the efficiency measure window glazing?

A. Window schedule for the building showing the major window glass types if more than one type of glass is present
B. Design building elevations marking the window glass specifications
C. Manufacturer's data sheets showing the make and model, U-value, and SHGC of the installed glass
D. Bill of quantities with the specifications for the window glass highlighted

Answer: C

Explanation:
The post-construction stage in EDGE certification requires evidence to confirm that the efficiency measures claimed in the design stage have been implemented as specified. For window glazing, which affects energy efficiency through its U-value (thermal transmittance) and SHGC (Solar Heat Gain Coefficient), the EDGE Certification Protocol provides clear requirements: "At the post-construction stage, the Client must provide manufacturer's data sheets for the window glazing measure, showing the make and model, U-value, and SHGC of the installed glass, to confirm that the glazing matches the specifications claimed in the self- assessment and meets the energy efficiency requirements" (EDGE Certification Protocol, Section 3.4: Post- Construction Requirements). Option C, manufacturer's data sheets showing the make and model, U-value, and SHGC of the installed glass, directly matches this requirement, as it provides the specific technical data needed to verify compliance. Option A (design building elevations marking the window glass specifications) is relevant at the design stage, not post-construction: "Design elevations are required at the preliminary stage to show intended glazing specifications, not after construction" (EDGE Certification Protocol, Section 3.2:
Audit Requirements). Option B (bill of quantities with specifications highlighted) is insufficient on its own, as it may not provide detailed technical data: "Bills of quantities may support purchase verification, but manufacturer's data sheets are required for technical specifications like U-value and SHGC" (EDGE Certification Protocol, Section 3.4: Post-Construction Requirements). Option D (window schedule showing major glass types) is helpful but not sufficient, as it lacks the detailed technical data: "Window schedules may indicate glass types, but they do not replace the need for manufacturer's data sheets with U-value and SHGC at post-construction" (EDGE User Guide, Section 6.2: Documentation Requirements). The EDGE User Guide further clarifies: "For glazing measures, post-construction evidence must confirm the installed product's performance through manufacturer's data sheets, ensuring alignment with the design-stage claims" (EDGE User Guide, Section 4.1: Insulation Measures). Thus, manufacturer's data sheets (Option C) are required at the post-construction stage.
Reference:EDGE Certification Protocol, Section 3.4: Post-Construction Requirements, Section 3.2: Audit Requirements; EDGE User Guide Version 2.1, Section 6.2: Documentation Requirements, Section 4.1:
Insulation Measures.

NEW QUESTION # 24
Variable speed drives in HVAC systems help:

A. Reduce energy consumption.
B. Increase the speed.
C. Reduce the speed.
D. Reduce water consumption.

Answer: A

Explanation:
Variable speed drives (VSDs) are a recognized energy efficiency measure in EDGE for optimizing HVAC system performance. The EDGE User Guide explains their role: "Variable speed drives in HVAC systems, such as those used in fans and pumps, adjust the motor speed to match the load demand, significantly reducing energy consumption compared to fixed-speed systems. This measure can achieve up to 30% energy savings in HVAC operations" (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Option C, reduce energy consumption, directly aligns with this description. Option A (reduce the speed) and Option B (increase the speed) are partially correct in that VSDs adjust speed, but the primary benefit in EDGE is energy savings, not speed adjustment itself: "The goal of VSDs in EDGE is energy reduction through speed modulation, not speed adjustment as an end" (EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics). Option D (reduce water consumption) is incorrect, as VSDs impact energy use, not water: "VSDs are an energy measure and do not directly affect water consumption in HVAC systems" (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Thus, VSDs help reduce energy consumption (Option C).
Reference:EDGE User Guide Version 2.1, Section 4.2: Energy Efficiency Measures; EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics.

NEW QUESTION # 25
Ceiling fans are an efficient way to increase air movement and therefore thermal comfort. Which of the following forms part of the evidence to demonstrate compliance at the design stage?

A. Computational Fluid Dynamics (CFD) assessment of all habitable spaces
B. Manufacturer's data sheet of the ceiling fans
C. Purchase receipts of the ceiling fans
D. Photographs of the installed ceiling fans

Answer: B

Explanation:
At the design stage (Preliminary Certification), EDGE requires specific documentation to verify that proposed measures, such as ceiling fans, will be implemented as claimed. The EDGE Certification Protocol specifies:
"For measures like ceiling fans at the design stage, the Client must provide evidence such as manufacturer's data sheets that detail the make, model, and specifications (e.g., power rating, air movement capacity) to confirm the fans meet the efficiency criteria for improving thermal comfort" (EDGE Certification Protocol, Section 3.2: Audit Requirements). Option C, manufacturer's data sheet of the ceiling fans, aligns with this requirement, as it provides the necessary specifications for verification. Option A (photographs of installed ceiling fans) is relevant at the post-construction stage, not design: "Photographs are required at the post- construction stage to confirm installation, not at the design stage" (EDGE Certification Protocol, Section 3.4:
Post-Construction Requirements). Option B (CFD assessment) is not required, as EDGE uses simplified calculations: "EDGE does not require CFD assessments for air movement; fan specifications suffice for design-stage verification" (EDGE Methodology Report Version 2.0, Section 5.5: Thermal Comfort Measures). Option D (purchase receipts) is also a post-construction requirement: "Purchase receipts verify installation, not design intent" (EDGE Certification Protocol, Section 3.4: Post-Construction Requirements).
Thus, the manufacturer's data sheet (Option C) is the correct evidence at the design stage.
Reference:EDGE Certification Protocol, Section 3.2: Audit Requirements, Section 3.4: Post-Construction Requirements; EDGE Methodology Report Version 2.0, Section 5.5: Thermal Comfort Measures.

NEW QUESTION # 26
Which of the following must be included in the EDGE Auditor submission for Preliminary Certification?

A. Compliance documents for selected measures.
B. The design audit site visit results verified by the EDGE Auditor.
C. The Chapter 5 EDGE certification protocol.
D. All of the available design data.

Answer: A

Explanation:
The EDGE Auditor's submission for Preliminary Certification (design stage) must include specific elements to support the recommendation for certification. The EDGE Certification Protocol specifies: "For Preliminary Certification, the EDGE Auditor's submission must include compliance documents for the selected measures, such as drawings, specifications, and manufacturer's data sheets, which verify that the design aligns with the self-assessment in the EDGE software. These documents are reviewed by the Certification Provider to confirm eligibility" (EDGE Certification Protocol, Section 3.2: Audit Requirements). Option C, compliance documents for selected measures, directly matches this requirement. Option A (all available design data) is too broad and not required: "Only documents directly related to the selected measures are needed, not all design data" (EDGE Certification Protocol, Section 3.2: Audit Requirements). Option B (Chapter 5 EDGE certification protocol) is incorrect, as this refers to the protocol document itself, not a submission component:
"The certification protocol is a reference, not part of the Auditor's submission" (EDGE Certification Protocol, Section 1.1: Overview). Option D (design audit site visit results) is incorrect, as site visits are not required at the design stage: "Preliminary Certification is based on a desk audit, not a site visit, which occurs at the post- construction stage" (EDGE Certification Protocol, Section 3.3: Certification Decision). Thus, compliance documents (Option C) are required in the submission.
Reference:EDGE Certification Protocol, Section 3.2: Audit Requirements, Section 3.3: Certification Decision, Section 1.1: Overview.

NEW QUESTION # 27
Which type of evidence is required at the post-construction stage for the efficiency measure window glazing?

A. Window schedule for the building showing the major window glass types if more than one type of glass is present
B. Design building elevations marking the window glass specifications
C. Manufacturer's data sheets showing the make and model, U-value, and SHGC of the installed glass
D. Bill of quantities with the specifications for the window glass highlighted

Answer: C

NEW QUESTION # 28
What will reduce the hot water demand in a hotel building?

A. Solar water heating
B. Solar photovoltaics (PVs)
C. Low-flow shower heads
D. Heat pumps for hot water

Answer: A,C,D

Explanation:
Reducing hot water demand in hotels is a key green building strategy in EDGE, focusing on both supply-side and demand-side measures. The EDGE User Guide details measures that reduce hot water demand: "Hot water demand in hotels can be reduced through supply-side measures like solar water heating and heat pumps for hot water, which decrease the energy needed to heat water, and demand-side measures like low-flow shower heads, which reduce the volume of hot water used" (EDGE User Guide, Section 5.2: Water Efficiency Measures, Section 4.2: Energy Efficiency Measures). Option B (solar water heating) reduces hot water demand by providing a renewable heat source, thus lowering energy use for heating. Option C (low-flow shower heads) directly reduces the volume of hot water used by limiting flow rates: "Low-flow shower heads can reduce hot water consumption by up to 30% in hotels" (EDGE Methodology Report Version 2.0, Section
4.2: Water Savings Calculations). Option D (heat pumps for hot water) reduces energy demand for heating water by using a more efficient system: "Heat pumps for hot water have a high COP, reducing the energy required to meet hot water demand" (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Option A (solar photovoltaics) generates electricity, not hot water, and does not directly reduce hot water demand:
"Solar PVs contribute to electricity generation, not hot water production" (EDGE Methodology Report Version 2.0, Section 5.3: Energy Measures). Thus, Options B, C, and D all reduce hot water demand in a hotel.
Reference:EDGE User Guide Version 2.1, Section 5.2: Water Efficiency Measures, Section 4.2: Energy Efficiency Measures; EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations, Section 5.3: Energy Measures.

NEW QUESTION # 29
EDGE was created for new buildings to promote:

A. Simple and scalable platform for green buildings.
B. Few exemplary high-performance buildings.
C. Highly accurate prediction of resource consumption.
D. Revenue for green building champions.

Answer: A

Explanation:
The purpose of EDGE, as defined by the International Finance Corporation (IFC), is to make green building accessible and scalable, particularly in emerging markets. The EDGE User Guide states: "EDGE was created by IFC to promote a simple and scalable platform for green buildings, enabling developers to achieve resource efficiency in new constructions through a user-friendly tool that focuses on energy, water, and materials savings" (EDGE User Guide, Section 1.1: Introduction to EDGE). Option C, a simple and scalable platform for green buildings, directly aligns with this mission. Option A (revenue for green building champions) is incorrect, as EDGE's goal is not financial gain for individuals but broader market transformation: "EDGE aims to transform the building sector, not to generate revenue for specific stakeholders" (EDGE Certification Protocol, Section 1.1: Overview). Option B (few exemplary high- performance buildings) contradicts EDGE's scalability focus: "EDGE is not about creating a few high- performance buildings but enabling widespread adoption of green practices" (EDGE User Guide, Section 1.1:
Introduction to EDGE). Option D (highly accurate prediction of resource consumption) is also incorrect, as EDGE prioritizes simplicity over precision: "EDGE uses simplified calculations for resource consumption, not highly accurate predictions, to ensure accessibility" (EDGE Methodology Report Version 2.0, Section 2.1:
Calculation Approach). Thus, EDGE promotes a simple and scalable platform (OptionC).
Reference:EDGE User Guide Version 2.1, Section 1.1: Introduction to EDGE; EDGE Certification Protocol, Section 1.1: Overview; EDGE Methodology Report Version 2.0, Section 2.1: Calculation Approach.

NEW QUESTION # 30
The Base Case for utility costs:

A. Excludes the cost of virtual energy.
B. Excludes the cost of virtual energy only in homes.
C. Includes the cost of virtual energy.
D. Includes the cost of virtual energy only in homes.

Answer: C

Explanation:
In EDGE, the Base Case is a standardized benchmark used to calculate utility cost savings, reflecting typical resource consumption for a building in its location and typology. The term "virtual energy" in EDGE refers to the energy required for heating, cooling, lighting, and other systems, modeled as if the building operates under typical conditions without efficiency measures. The EDGE User Guide explains how utility costs are calculated: "The Base Case for utility costs includes the cost of virtual energy, which represents the modeled energy consumption for the building type in the absence of efficiency measures, alongside water consumption, using localtariffs to estimate financial impacts" (EDGE User Guide, Section 2.3: Using the EDGE App). Option B, includes the cost of virtual energy, aligns with this approach, as the Base Case accounts for all modeled energy use to establish a baseline for savings. Option A (excludes the cost of virtual energy) is incorrect, as virtual energy is a core component of the Base Case: "Virtual energy in EDGE is the theoretical energy use calculated for the Base Case, including heating, cooling, and lighting, and its cost is always included in utility cost calculations" (EDGE Methodology Report Version 2.0, Section 4.4: Cost Savings Calculations). Option C (excludes the cost of virtual energy only in homes) and Option D (includes the cost of virtual energy only in homes) are also incorrect, as the treatment of virtual energy is consistent across all typologies: "The Base Case methodology, including the inclusion of virtual energy costs, applies uniformly to all building types in EDGE, whether homes, hotels, or offices, to ensure a fair comparison of savings" (EDGE User Guide, Section 2.3: Using the EDGE App). The EDGE Methodology Report further clarifies: "Utility costs in the Base Case are derived from virtual energy and water consumption, reflecting typical usage patterns for the building type and location, ensuring that savings calculations are comprehensive and include all relevant energy demands" (EDGE Methodology Report Version 2.0, Section 4.4: Cost Savings Calculations). This consistent inclusion of virtual energy costs across all typologies makes Option B the correct answer.
Reference:EDGE User Guide Version 2.1, Section 2.3: Using the EDGE App; EDGE Methodology Report Version 2.0, Section 4.4: Cost Savings Calculations.

NEW QUESTION # 31
In a 3-star business hotel near the city center, which of the following elements of the building's water use breakdown is/are likely to consume the most water?

A. Toilets in lobby area
B. Showers in guest rooms
C. Laundry
D. Faucets in guest rooms

Answer: B

Explanation:
Water consumption in hotels varies significantly based on usage patterns, with guest-related activities often dominating the water use breakdown. The EDGE User Guide provides detailed insights into water use in hotels: "In a typical 3-star business hotel, the largest contributor to water consumption is showers in guest rooms, accounting for approximately 40-50% of total water use due to frequent guest showers, especially in urban hotels with high occupancy. Laundry, toilets, and faucets also contribute, but to a lesser extent, with laundry at 15-20%, toilets at 10-15%, and faucets at 5-10%" (EDGE User Guide, Section 5.2: Water Efficiency Measures). Option A, showers in guest rooms, aligns with this breakdown as the element likely to consume the most water. Option B (laundry) is significant but lower than showers: "Laundry in 3-star hotels consumes less water than showers, as laundry is typically centralized and less frequent than daily guest showers" (EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations). Option C (toilets in lobby area) is a minor contributor, as lobby toilets serve fewer users compared to guest rooms:
"Toilets in public areas like the lobby have lower usage compared to guest room facilities, contributing only a small fraction of total water use in hotels" (EDGE User Guide, Section 5.2: Water Efficiency Measures).
Option D (faucets in guest rooms) also uses less water than showers: "Faucets in guest rooms, used for handwashing or brushing teeth, have lower flow rates and usage frequency compared to showers, which often run for 5-10 minutes per use" (EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations). The EDGE User Guide further elaborates: "In business hotels, showers dominate water use due to high occupancy and guest behavior, making measures like low-flow shower heads particularly effective for water savings" (EDGE User Guide, Section 5.2: Water Efficiency Measures). The EDGE Methodology Report adds: "For a 3-star hotel with 100 rooms and 70% occupancy, showers can account for 45 liters per guest per day, compared to 15 liters for laundry, 10 liters for toilets, and 5 liters for faucets, based on standard usage assumptions" (EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations).
Thus, showers in guest rooms (Option A) are likely to consume the most water in this context.
Reference:EDGE User Guide Version 2.1, Section 5.2: Water Efficiency Measures; EDGE Methodology Report Version 2.0, Section 4.2: Water Savings Calculations.

NEW QUESTION # 32
The Client informs an EDGE Auditor that a key member of the design team has resigned. The Client requests the Auditor to take the member's place for the remainder of the project's design development as it would provide the Auditor an opportunity to identify suitable green building measures, making audit tasks much simpler. What should the EDGE Auditor do?

A. Resign from the audit role on the basis that its position has been compromised by this direct approach by the Client.
B. Accept the additional commission on the basis that this will save the Client time and money, and would reduce the volume of work required for the audit.
C. Refer the Client to an associate within the organization who works in another department, but is qualified and available to carry out the work.
D. Refer the Client to an associate within the organization who will be working with the Auditor on the EDGE audit, since the Auditor organization has spare capacity.

Answer: C

Explanation:
The EDGE framework strictly prohibits Auditors from engaging in roles that could compromise their independence, such as providing design consultancy on the same project they are auditing. The EDGE Expert and Auditor Protocols address this scenario explicitly: "An EDGE Auditor must not accept any role in the design development of a project they are auditing, as this creates a conflict of interest by blurring the lines between consultancy and independent verification. If the Client requests the Auditor to take on a design role, the Auditor should decline and may refer the Client to another qualified professional who is not involved in the audit process" (EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest). Option B, refer the Client to an associate within the organization who works in another department, but is qualified and available to carry out the work, aligns with this guidance, as it maintains the Auditor's independence while helping the Client find a suitable replacement. Option A (resign from the audit role) is an overreaction, as the request itself does not compromise the Auditor's position unless accepted: "The Auditor is not required to resign unless they have already engaged in a conflicting role, which can be avoided by declining the request" (EDGE Expert and Auditor Protocols, Section 4.1: Audit Process). Option C (accept the additional commission) is unethical, as it violates conflict-of-interest rules: "Accepting a design role on a project being audited undermines the Auditor's impartiality, as they would be auditing theirown work, which is strictly prohibited" (EDGE Certification Protocol, Section 3.1: Certification Process). Option D (refer the Client to an associate working with the Auditor on the EDGE audit) is also incorrect, as this associate is already involved in the audit, creating a potential conflict: "Referring the Client to someone involved in the same audit does not resolve the conflict of interest, as the audit team must remain independent from design activities" (EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest). The EDGE User Guide reinforces this principle: "Auditors must maintain strict separation from design roles to ensure an unbiased audit, and should assist the Client by referring them to independent professionals if needed" (EDGE User Guide, Section 6.5:
Working with EDGE Auditors). Thus, referring the Client to a qualified associate in another department (Option B) is the correct action.
Reference:EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest, Section 4.1: Audit Process; EDGE Certification Protocol, Section 3.1: Certification Process; EDGE User Guide Version 2.1, Section 6.5:
Working with EDGE Auditors.

NEW QUESTION # 33
The Client has sent a copy of the local occupancy permit for a project being audited. This permit:

A. Replaces the need to audit EDGE Materials measures.
B. Does not replace the need to audit all EDGE measures.
C. Does not replace the need for desktop studies.
D. Replaces the need to audit all EDGE measures.

Answer: B

Explanation:
An occupancy permit indicates that a building meets local regulatory requirements for occupancy,but it does not address the specific green building measures required for EDGE certification. The EDGE Certification Protocol clearly outlines the role of such permits in the audit process: "A local occupancy permit provided by the Client confirms that the building complies with local building codes and is ready for use. However, it does not replace the need to audit all EDGE measures, as EDGE certification requires verification of specific energy, water, and materials efficiency measures that are not typically covered by local permits" (EDGE Certification Protocol, Section 3.4: Post-Construction Requirements). Option A, does not replace the need to audit all EDGE measures, directly aligns with this guidance, as the Auditor must still verify each claimed measure (e.g., insulation, low-flow fixtures, fly ash concrete) against EDGE standards. Option B (replaces the need to audit all EDGE measures) is incorrect, as the permit does not address EDGE-specific requirements:
"Local permits do not verify EDGE measures like energy savings or embodied energy reductions, so a full audit is still required" (EDGE Expert and Auditor Protocols, Section 4.4: Site Audit Procedures). Option C (does not replace the need for desktop studies) is partially correct but less comprehensive, as desktop studies are only one part of the audit process: "Desktop studies are part of the audit, but the occupancy permit does not exempt any aspect of the EDGE audit, including site visits and measure verification" (EDGE Certification Protocol, Section 3.2: Audit Requirements). Option D (replaces the need to audit EDGE Materials measures) is also incorrect, as materials measures (e.g., use of fly ash concrete) require specific evidence like manufacturer's data sheets, not covered by an occupancy permit: "Materials measures require detailed documentation of embodied energy reductions, which local permits do not address" (EDGE User Guide, Section 7.2: Materials Efficiency Measures). The EDGE User Guide further reinforces: "The Auditor must verify all EDGE measures through appropriate documentation and site visits, regardless of local permits, to ensure compliance with the EDGE standard" (EDGE User Guide, Section 6.3: Post-Construction Certification). Thus, the occupancy permit does not replace the need to audit all EDGE measures (Option A).
Reference:EDGE Certification Protocol, Section 3.4: Post-Construction Requirements, Section 3.2: Audit Requirements; EDGE Expert and Auditor Protocols, Section 4.4: Site Audit Procedures; EDGE User Guide Version 2.1, Section 6.3: Post-Construction Certification, Section 7.2: Materials Efficiency Measures.

NEW QUESTION # 34
Which of the following is an EDGE measure to reduce the embodied energy in materials?

A. Occupancy sensors
B. External shading
C. Low-flow shower heads
D. Fly ash concrete

Answer: D

Explanation:
Embodied energy in materials is one of the three core pillars of the EDGE standard, focusing on reducing the environmental impact of construction materials. The EDGE User Guide lists measures that specifically target embodied energy: "To reduce embodied energy in materials, EDGE includes measures such as the use of fly ash concrete, which substitutes a portion of cement with fly ash, a byproduct of coal combustion, thereby lowering the embodied energy and carbon footprint of concrete production" (EDGE User Guide, Section 7.2:
Materials Efficiency Measures). Option B, fly ash concrete, directly aligns with this measure, as it reduces the need for high-energy cement production. Option A (external shading) impacts energy by reducing cooling loads but does not directly address embodied energy: "External shading reduces operational energy use but does not contribute to embodied energy savings unless the shading materials themselves are low-impact, which is not specified in EDGE" (EDGE User Guide, Section 3.5: Passive Design Strategies). Option C (occupancy sensors) is an energy efficiency measure for lighting, not materials: "Occupancy sensors reduce lighting energy use but have no direct impact on embodied energy in materials" (EDGE User Guide, Section
4.4: Lighting Efficiency Measures). Option D (low-flow shower heads) targets water efficiency, not materials:
"Low-flow shower heads reduce water consumption, but their embodied energy impact is minimal and not a focus of EDGE materials measures" (EDGE User Guide, Section 5.2: Water Efficiency Measures). The EDGE MethodologyReport further elaborates: "Fly ash concrete can reduce embodied energy by up to 20% compared to traditional concrete, making it a key measure in EDGE for materials efficiency, especially in high-volume applications like hospitals or hotels" (EDGE Methodology Report Version 2.0, Section 6.1:
Embodied Energy in Materials). Other materials measures in EDGE, such as using recycled steel or bamboo, are not listed among the options, making fly ash concrete (Option B) the correct choice for reducing embodied energy.
Reference:EDGE User Guide Version 2.1, Section 7.2: Materials Efficiency Measures, Section 3.5: Passive Design Strategies, Section 4.4: Lighting Efficiency Measures, Section 5.2: Water Efficiency Measures; EDGE Methodology Report Version 2.0, Section 6.1: Embodied Energy in Materials.

NEW QUESTION # 35
Which of the following BEST describes an EDGE Expert?

A. An individual accredited by the EDGE Operations and Management Team who can serve as a consultant
B. An individual who can serve as both an auditor and a consultant upon EDGE Committee approval
C. A consultant who can issue a preliminary EDGE certificate
D. An individual accredited by the EDGE Certifier who can serve as a consultant

Answer: D

Explanation:
The role of an EDGE Expert is well-defined within the EDGE framework to clarify their responsibilities and qualifications. The EDGE Expert and Auditor Protocols provide a precise description: "An EDGE Expert is an individual accredited by the EDGE Certifier (such as GBCI or other authorized certification bodies) who can serve as a consultant to project teams, advising on the selection of green building measures, preparing the self-assessment in the EDGE software, and guiding the project toward certification" (EDGE Expert and Auditor Protocols, Section 2.1: Roles of EDGE Expert). Option B, an individual accredited by the EDGE Certifier who can serve as a consultant, directly matches this definition. Option A (a consultant who can issue a preliminary EDGE certificate) is incorrect, as Experts do not issue certificates: "Only the EDGE Certification Provider can issue a preliminary certificate, not the EDGE Expert" (EDGE Certification Protocol, Section 3.3: Certification Decision). Option C (an individual who can serve as both an auditor and a consultant upon EDGE Committee approval) is also incorrect, as this violates conflict-of-interest rules: "An individual cannot serve as both an EDGE Expert and Auditor on the same project, even with committee approval, to avoid conflicts of interest" (EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest). Option D (an individual accredited by the EDGE Operations and Management Team) is wrong, as accreditation is handled by the Certifier, not the Operations team: "The EDGE Operations and Management Team oversees the program, while accreditation of Experts is managed by the EDGE Certifier" (EDGE Certification Protocol, Section 1.3: Program Structure). The EDGE User Guide further supports this: "EDGE Experts are accredited professionals who consult on projects, having passed the EDGE Expert exam administered through the Certifier" (EDGE User Guide, Section 6.4: Working with EDGE Experts). Thus, Option B best describes an EDGE Expert.
Reference:EDGE Expert and Auditor Protocols, Section 2.1: Roles of EDGE Expert, Section 2.3: Conflict of Interest; EDGE Certification Protocol, Section 3.3: Certification Decision, Section 1.3: Program Structure; EDGE User Guide Version 2.1, Section 6.4: Working with EDGE Experts.

NEW QUESTION # 36
Which of the following hot water technologies is from a renewable source?

A. High efficiency boiler for water heating
B. Preheating water using waste heat from the generator
C. Ground source heat pump
D. Solar hot water collectors

Answer: D

Explanation:
EDGE recognizes renewable energy sources for their contribution to reducing carbon emissions in hot water production. The EDGE User Guide defines renewable hot water technologies: "Solar hot water collectors are considered a renewable source in EDGE, as they directly use solar energy to heat water, reducing reliance on fossil fuel-based energy" (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Option B, solar hot water collectors, matches this description as it harnesses solar energy, a renewable resource. Option A (ground source heat pump) uses electricity to transfer heat from the ground, which is efficient but not renewable unless the electricity is from a renewable source: "Ground source heat pumps are efficient but rely on electrical input, not classified as a renewable source in EDGE" (EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics). Option C (high efficiency boiler) typically uses gas or electricity, not a renewable source: "Boilers, even high-efficiency ones, are not renewable as they burn fuel or use grid electricity" (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Option D (preheating water using waste heat from the generator) is a heat recovery method, not a renewable source: "Waste heat recovery improves efficiency but is not considered a renewable energy source in EDGE" (EDGE Methodology Report Version 2.0, Section 5.3: Energy Measures). Thus, solar hot water collectors (Option B) is the renewable source technology.
Reference:EDGE User Guide Version 2.1, Section 4.2: Energy Efficiency Measures; EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics, Section 5.3: Energy Measures.

NEW QUESTION # 37
Is it possible to be both the EDGE Expert and Auditor on a project?

A. Yes, but only in the case that there are no other EDGE Auditors available for the project.
B. No, even if EDGE Certifier agrees to special terms to have no conflict of interest.
C. No, an EDGE Expert cannot be the EDGE Auditor on the same project.
D. Yes, they can be both an EDGE Auditor and EDGE Expert in all cases.

Answer: C

Explanation:
The EDGE framework strictly enforces separation of roles to maintain integrity and avoid conflicts of interest during the certification process. The EDGE Expert and Auditor Protocols explicitly address this issue: "An individual cannot serve as both the EDGE Expert and EDGE Auditor on the same project. This separation ensures independence in the audit process, as the Expert's role as a consultant advising the project team could bias the Auditor's objective assessment of the project's compliance with EDGE standards" (EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest). Option A, no, an EDGE Expert cannot be the EDGE Auditor on the same project, directly reflects this rule. Option B (no, even if the Certifier agrees to special terms) adds an unnecessary condition, as the protocols do not allow exceptions: "No exceptions are permitted for an individualto serve in both roles on the same project, regardless of agreements or special terms" (EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest). Option C (yes, in all cases) is incorrect, as it contradicts the conflict-of-interest rules: "Allowing dual roles in all cases would undermine the impartiality required for certification" (EDGE Certification Protocol, Section 3.1: Certification Process). Option D (yes, if no other Auditors are available) is also incorrect, as availability does not override the conflict-of-interest prohibition: "Even if no other Auditors are available, the roles must remain separate; the Client must find a different Auditor or delay the audit" (EDGE Expert and Auditor Protocols, Section 4.1: Audit Process). The EDGE User Guide reinforces this principle: "The separation of Expert and Auditor roles ensures a fair and unbiased certification process, protecting the credibility of EDGE certification" (EDGE User Guide, Section
6.4: Working with EDGE Experts). Thus, it is not possible to be both (Option A).
Reference:EDGE Expert and Auditor Protocols, Section 2.3: Conflict of Interest, Section 4.1: Audit Process; EDGE Certification Protocol, Section 3.1: Certification Process; EDGE User Guide Version 2.1, Section 6.4:
Working with EDGE Experts.

NEW QUESTION # 38
In the EDGE software, the Base Case selection of external wall materials in hotels relies on information derived from:

A. Typical building practices as well as national building performance codes, where they are in existence.
B. Hotel developers' corporate standard specifications, or materials which have been accredited by the hotel industry.
C. Local building material suppliers who subscribe to EDGE certification for their materials, or are nationally accredited by the local standards authority.
D. Global building practices as well as international building performance codes, where they are in existence.

Answer: A

Explanation:
The EDGE software uses a Base Case to establish a benchmark for resource consumption, tailored to local conditions. The EDGE Methodology Report explains how the Base Case is constructed: "The Base Case for external wall materials in hotels is determined using data from market surveys of typical building practices in the project's country, supplemented by national building performance codes where available. This ensures the baseline reflects local construction norms and regulatory standards" (EDGE Methodology Report Version 2.0, Section 3.1: Base Case Determination). Option A matches this description by referencing typical building practices and national codes. Option B incorrectly refers to global practices and international codes, which EDGE does not use, as the software prioritizes local context. Option C, focusing on corporate specifications, is not part of the Base Case methodology, as the Base Case is standardized, not project-specific. Option D, involving local suppliers or accreditation, is irrelevant to how EDGE determines the Base Case, which relies on broader market data rather than supplier-specificinformation.
Reference:EDGE Methodology Report Version 2.0, Section 3.1: Base Case Determination; EDGE User Guide Version 2.1, Section 2.3: Using the EDGE App.

NEW QUESTION # 39
Which of the following is a primary resource for the EDGE Auditor when performing the site visit?

A. EDGE software
B. Roof insulation U-value
C. Window to Wall Ratio (WWR)
D. EDGE Auditor's checklist

Answer: D

Explanation:
During a site visit for post-construction certification, the EDGE Auditor relies on specific tools to verify compliance. The EDGE Expert and Auditor Protocols specify: "The primary resource for an EDGE Auditor during a site visit is the EDGE Auditor's checklist, which provides a structured list of items to verify, including the implementation of selected measures, alignment with the self-assessment, and compliance with EDGE standards" (EDGE Expert and Auditor Protocols, Section 4.4: Site Audit Procedures). Option C, EDGE Auditor's checklist, matches this description as the key resource guiding the audit process. Option A (EDGE software) is a tool for assessment, not a resource for the site visit: "The EDGE software is used for self-assessment and desk audits, not directly during site visits" (EDGE Certification Protocol, Section 3.2:
Audit Requirements). Option B (roof insulation U-value) and Option D (Window to Wall Ratio) are specific data points the Auditor may verify, not primary resources: "U-values and WWR are elements to check, not tools for the Auditor" (EDGE Expert and Auditor Protocols, Section 4.4: Site Audit Procedures). The checklist ensures all aspects of the project are systematically reviewed, making it the primary resource (Option C).
Reference:EDGE Expert and Auditor Protocols, Section 4.4: Site Audit Procedures; EDGE Certification Protocol, Section 3.2: Audit Requirements.

NEW QUESTION # 40
The COP of the water-cooled chiller is 6, and the cooling thermal load is 3516 W. What is the power rating of the chiller?

A. 586 W
B. 3522 W
C. 21096 W
D. 3510 W

Answer: A

Explanation:
The Coefficient of Performance (COP) is used in EDGE to calculate the electrical power input required for a given thermal output of a chiller. The EDGE Methodology Report defines COP as: "COP is the ratio of thermal output to electrical input, expressed as COP = Thermal Output / Electrical Input. To find the electrical input (power rating), rearrange the formula: Electrical Input = Thermal Output / COP" (EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics). Given the COP of the water-cooled chiller as 6 and the cooling thermal load (thermal output) as 3516 W, the power rating is calculated as follows: Electrical Input = 3516 W / 6 = 586 W. Option A, 586 W, matches this calculation. Option B (3510 W) is incorrect, as it is slightly less than the thermal output, implying an unrealistic COP near 1. Option C (3522 W) is slightly above the thermal output, also incorrect. Option D (21096 W) is the result of multiplying the thermal output by the COP (3516 × 6), which is the inverse of the correct calculation. The EDGE User Guide confirms: "For a chiller with a COP of 6, the electrical input is one-sixth of the thermal output, ensuring energy efficiency is accurately assessed" (EDGE User Guide, Section 4.2: Energy Efficiency Measures). Thus, the power rating is
586 W (Option A).
Reference:EDGE Methodology Report Version 2.0, Section 5.1: Energy Efficiency Metrics; EDGE User Guide Version 2.1, Section 4.2: Energy Efficiency Measures.

NEW QUESTION # 41
Which of the following protocols should be followed when the project city is not listed in the EDGE App?

A. Choose the closest city to the project location and edit the climate data if necessary.
B. Write to EDGE Certifier to request the city to be included and wait for the application to be updated.
C. Choose the capital city to the project location and edit the climate data if necessary.
D. Select any city in the same climate zone around the world and use that to certify the project.

Answer: A

Explanation:
The EDGE App relies on location-specific climate data to calculate resource savings, but not all cities are listed. The EDGE User Guide provides guidance for such cases: "If the project city is not listed in the EDGE App, the user should choose the closest city to the project location that is available in the database. If necessary, the user can edit the climate data (e.g., temperature, humidity) to better reflect the project's actual conditions, ensuring accurate calculations" (EDGE User Guide, Section 2.2: Project Setup). Option B, choose the closest city and edit the climate data if necessary, directly matches this protocol. Option A (write to EDGE Certifier and wait) is incorrect, as this is not a required step: "Users are not required to request new cities; they can proceed by selecting the closest city" (EDGE User Guide, Section 2.2: Project Setup). Option C(select any city in the same climate zone globally) is too broad and inaccurate: "Choosing a city from a different region, even in the same climate zone, may lead to incorrect assumptions about local practices and climate" (EDGE Methodology Report Version 2.0, Section 3.2: Climate Data Inputs). Option D (choose the capital city) is also incorrect unless it is the closest: "The capital city should only be selected if it is the nearest available option in the database" (EDGE User Guide, Section 2.2: Project Setup). Thus, the correct protocol is to choose the closest city and edit climate data (Option B).
Reference:EDGE User Guide Version 2.1, Section 2.2: Project Setup; EDGE Methodology Report Version
2.0, Section 3.2: Climate Data Inputs.

NEW QUESTION # 42
Who are licensed to train candidates as EDGE Experts and EDGE Auditors?

A. EDGE Auditors
B. EDGE Certification Providers
C. EDGE Faculty
D. Accredited EDGE Experts

Answer: C

Explanation:
Training for EDGE Experts and Auditors is a structured process managed by specific entities authorized by the IFC. The EDGE Expert and Auditor Protocols specify: "EDGE Faculty are licensed by IFC to deliver training for candidates aspiring to become EDGE Experts and EDGE Auditors. These trainers are selected and trained by IFC to ensure consistency and quality in the delivery of EDGE training programs" (EDGE Expert and Auditor Protocols, Section 3.2: Training Requirements). Option A, EDGE Faculty, directly matches this description. Option B (EDGE Auditors) is incorrect, as auditors perform audits, not training, per the protocols: "EDGE Auditors are responsible for verifying project compliance, not for training others" (EDGE Expert and Auditor Protocols, Section 2.2: Roles). Option C (EDGE Certification Providers) is also incorrect, as their role is to issue certifications, not conduct training: "Certification Providers like GBCI issue EDGE certificates but do not train candidates" (EDGE Certification Protocol, Section 1.3: Certification Process).
Option D (Accredited EDGE Experts) is wrong, as Experts advise on projects, not train others, as per the protocols: "EDGE Experts provide consultancy services to project teams" (EDGE Expert and Auditor Protocols, Section 2.1: Roles).
Reference:EDGE Expert and Auditor Protocols, Section 3.2: Training Requirements, Section 2.1: Roles, Section 2.2: Roles; EDGE Certification Protocol, Section 1.3: Certification Process.

NEW QUESTION # 43
......

Resources From:

2026 Latest BraindumpsVCE EDGE-Expert Exam Dumps (PDF & Exam Engine) Free Share: https://www.braindumpsvce.com/EDGE-Expert_exam-dumps-torrent.html
2026 Latest BraindumpsVCE EDGE-Expert PDF and EDGE-Expert Exam Dumps Free Share: https://drive.google.com/open?id=13ju1BdwUKgxVS7MDihdciTaIMntqxKrK

Free Resources from BraindumpsVCE, We Devoted to Helping You 100% Pass All Exams!

[Feb-2026] EDGE-Expert Free PDF from BraindumpsVCE [Q22-Q43]

Related Articles